Get CWNP CWNA-109 Exam Dumps

Answer : A

OFDMA is a new modulation scheme introduced in 802.11ax that allows multiple users to share the same channel by dividing it into smaller subchannels called resource units (RUs). This improves the efficiency and capacity of the WLAN by reducing contention and overhead. However, to use OFDMA, both the AP and the client must support 802.11ax and negotiate the parameters of the subchannel allocation.Therefore, the customer needs to upgrade the clients that require OFDMA to 802.11ax devices12.

The other options are not correct because they do not reflect the reality of OFDMA.Option B is incorrect because OFDMA is a mandatory feature of 802.11ax for both downlink and uplink transmissions, and all 802.11ax APs must support it1. Option C is incorrect because OFDM and OFDMA are different modulation schemes, and OFDM does not allow multiple users to share the same channel.Option D is incorrect because 802.11ac devices cannot support OFDMA through driver upgrades, as they lack the hardware and firmware capabilities to do so2.

Answer : B

A possible cause of a sudden change in performance for the laptop computers is thata new tenant in the building has set their AP to the same RF channel that your customer is using. This can create co-channel interference (CCI), which is a situation where two or more APs or devices use the same or overlapping channels in the same area. CCI can degrade the performance of WLANs by increasing contention, collisions, retransmissions, and latency. CCI can also reduce the effective range and throughput of WLANs by lowering the signal-to-noise ratio (SNR). To avoid or mitigate CCI, it is recommended to use non-overlapping channels, adjust transmit power levels, or implement channel management techniques such as dynamic frequency selection (DFS) or load balancing. The sky condition, antenna position, or Bluetooth headset are not likely to cause a sudden change in performance for the laptop computers.Reference:[CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 81; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 71.

Answer : D

The feature of 802.11ax (HE) that provides this functionality isOFDM

A . OFDMA stands for Orthogonal Frequency Division Multiple Access and is a technology that allows multiple devices to communicate simultaneously on the same channel in the same BSS. OFDMA works by dividing a channel into smaller subchannels called Resource Units (RUs), which are composed of groups of subcarriers or tones. Each RU can be assigned to a different device based on its bandwidth requirement and signal quality. This way, OFDMA can increase the efficiency and capacity of the channel by reducing overhead, contention, and latency. OFDMA can also support both uplink and downlink multi-user transmissions using trigger frames and buffer status reports. 6 GHz support, TWT, and Wi-Fi-LTE are not features of 802.11ax that provide this functionality.Reference:[CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 226; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 216.

Answer : A

An immediate concern that you note after hearing this information is thatthe power budget in the edge switches must be carefully planned and monitored based on the number of supported PoE devices. PoE stands for Power over Ethernet and is a technology that allows Ethernet switches to deliver power along with data to devices such as VoIP phones and 802.11 access points. PoE devices are classified into different classes based on their power consumption and output. The edge switches have a limited power budget that determines how many PoE devices they can support simultaneously. If the power budget is exceeded, some PoE devices may not receive enough power or may shut down unexpectedly. Therefore, it is important to plan and monitor the power budget in the edge switches based on the number and class of PoE devices connected to them. Using Ether-channel, placing switches in optimal locations, or avoiding distortion are not immediate concerns related to PoE devices.Reference:[CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 234; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 224.

Answer : D

What you should tell him is thatdue to 802.11 network operations and the dynamic rates used by devices on the network, the two radios will likely not exceed the 1 Gbps Ethernet link. This is because the actual throughput of an 802.11 network is much lower than the theoretical data rates due to factors such as overhead, contention, interference, retransmissions, and environmental conditions. Moreover, the data rates used by devices on the network vary depending on their distance, signal quality, capabilities, and configuration. Therefore, it is unlikely that both radios of the AP will simultaneously use the maximum data rates and saturate the 1 Gbps Ethernet link. Upgrading to a 10 Gbps Ethernet link or running a second 1 Gbps Ethernet link may be unnecessary and costly. Compressing all data before transmitting it onto the Ethernet link may introduce additional overhead and latency.Reference:[CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 227; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 217.