Get Juniper JN0-370 Exam Dumps

user@qfabric> show fabric administration inventory node-groups RSNG-1 detail

Node group: RSNG-1, Connected, Configured

Connection uptime: 0:01:22

Node device: Node-2, Disconnected

Member id: 0

Node device. Node-3, Connected,

Member id: 1

Node group master: Yes

Which two statements are true regarding the output shown in the Above? (Choose two.)

[edit class-of-service schedulers]

user@qfabric# show

fcoe_sh {

transmit-rate 6g;

}

lan_sh {

transmit-rate 4g;

}

You are asked to guarantee that an application receives a minimum of 1 Gbps of bandwidth. Which action would meet this requirement?

Inventory name for the remote node

DRE-0 Diagnostic routing engine

FC-0 Fabric control

FC-1 Fabric control

FM-0 Fabric manager

NW-NG-0 Node group

p3603-c Node Group

p4186-c Node Group

p4840-c/RE0 Interconnect device control board

Once the Director group is up and initially configured, you want to connect to a Node group. which command should you use?

user@qfabric> show ethernet-switching interfaces

Interface State VLAN members Tag Tagging Blocking

RSNG-1:ae0.0 down v50 50 tagged Disabled by bpdu-control

v51 51 tagged Disabled by bpdu-control

v52 52 tagged Disabled by bpdu-control

v53 53 tagged Disabled by bpdu-control

Which two steps should you take to make RSNG-1:ae0.0 operational? (Choose two.)

On node2:

user@node2> show ethernet-switching table

Ethernet-switching tablE. 119 entries, 104 learned

VLAN MAC address Type Age Interfaces

vlan200 * Flood - N2:All-members

N3:All-members

N4:All-members

vlan200 00:00:02:00:00:01 Learn 0 N2:ae0.0

vlan200 00:00:02:00:00:02 Learn 0 N2:ae0.0

vlan200 00:00:02:00:00:03 Learn 0 N2:ae0.0

vlan200 00:00:02:00:00:06 Learn 0 N2:ae0.0

On node5:

user@node5> show ethernet-switching table

Ethernet-switching tablE. 119 entries, 104 learned

VLAN MAC address Type Age Interfaces

vlan200 * Flood - N2:All-members

N3:All-members

N4:All-members

vlan200 00:00:05:00:00:01 Learn 0 N5:ae0.0

vlan200 00:00:05:00:00:02 Learn 0 N5:ae0.0

vlan200 00:00:05:00:00:03 Learn 0 N5:ae0.0

vlan200 00:00:05:00:00:06 Learn 0 N5:ae0.0

user@node5>show route forwarding-table family ethernet-switching vlan vlan200---qfabric

Routing tablE. default.ethernet-switching

Destination Type RtRef Next hop Type Index NhRef Netif

7, * user 0 comp 1676 2

7, * intf 0 rslv 1650 1

7, 00:00:02:00:00:01 user 0 comp 1673 51

7, 00:00:02:00:00:02 user 0 comp 1673 51

7, 00:00:02:00:00:03 user 0 comp 1673 51

7, 00:00:02:00:00:05 user 0 comp 1673 51

7, 00:00:02:00:00:06 user 0 comp 1673 51

user@qfabric>show route fabric table default.bridge.0 bridge-route-mac-address

00:00:02:00:00:01

default.bridge.0: 110 destinations, 165 routes (110 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both

Host A on Node device node2 and Host B on Node device node5 are on

the same VLAN but Host A cannot ping Host B

Host A's MAC address is 00:00:02:00:00:01.

Host B's MAC address is 00:00:05:00:00:01.

What is causing this problem?