Get iSQI CTFL_Syll_4.0 Exam Dumps

Answer : D

The test leader is the person who is responsible for planning, monitoring, and controlling the test activities and resources in a test project. The test leader should have the best knowledge of the test objectives, scope, risks, resources, schedule, and quality criteria.The test leader should also be aware of the test automation criteria, such as the execution frequency, the test support, the team education, the roles and responsibilities, and the devs and testers collaboration1. Based on these factors, the test leader can decide which tests are suitable for automation and which are not, and prioritize them accordingly.The test leader can also coordinate with the test automation engineers, the developers, and the stakeholders to ensure the alignment of the test automation strategy with the test project goals and expectations.Reference= ISTQB Certified Tester Foundation Level (CTFL) v4.0 Syllabus, Chapter 2, Section 2.3.1, Page 152; ISTQB Glossary of Testing Terms v4.0, Page 403; ISTQB Certified Tester Foundation Level (CTFL) v4.0 Syllabus, Chapter 6, Section 6.1.1, Page 514; Top 8 Test Automation Criteria You Need To Fulfill - QAMIND1

Answer : D

According to the ISTQB Certified Tester Foundation Level (CTFL) v4.0, the life cycle of a defect typically follows a sequence from its discovery to its closure. In the provided figure, it starts with S0 (New), moves to S1 (Assigned), then to S2 (Resolved), followed by S3 (Verified). If the defect is not fixed, it can be Re-opened (S5) and goes back for verification (S3). Once verified, it is Closed (S4).Reference: ISTQB Certified Tester Foundation Level (CTFL) v4.0 Syllabus, Section 1.4.3, Page 17.

Answer : A

Project risks are the uncertainties or threats that may affect the project objectives, such as scope, schedule, cost, and quality. According to the ISTQB Certified Tester Foundation Level (CTFL) v4.0 syllabus, some of the factors that contribute to project risks are:

Skill and staff shortages: This factor refers to the lack of adequate or qualified human resources to perform the project tasks. This may result in delays, errors, rework, or low productivity.

Problems in defining the right requirements: This factor refers to the difficulties or ambiguities in eliciting, analyzing, specifying, validating, or managing the requirements of the project. This may result in misalignment, inconsistencies, gaps, or changes in the requirements, affecting the project scope and quality.

Contractual issues: This factor refers to the challenges or disputes that may arise from the contractual agreements between the project parties, such as clients, suppliers, vendors, or subcontractors. This may result in legal, financial, or ethical risks, affecting the project delivery and satisfaction.

The other options are not correct because they list factors that contribute to PRODUCT risks, not project risks. Product risks are the uncertainties or threats that may affect the quality or functionality of the software product or system. Some of the factors that contribute to product risks are:

Poor software quality characteristics: This factor refers to the lack of adherence or compliance to the quality attributes or criteria of the software product or system, such as reliability, usability, security, performance, or maintainability. This may result in defects, failures, or dissatisfaction of the users or stakeholders.

Software does not perform its intended functions: This factor refers to the deviation or discrepancy between the expected and actual behavior or output of the software product or system. This may result in errors, faults, or malfunctions of the software product or system.

Reference= ISTQB Certified Tester Foundation Level (CTFL) v4.0 syllabus, Chapter 1: Fundamentals of Testing, Section 1.5: Risks and Testing, Pages 14-16.

Answer : B

Covering all transitions at least once is the highest coverage criterion for state transition based test cases, because it ensures that every possible change of state is tested at least once. This means that all the events that trigger the transitions, as well as the actions and outputs that result from the transitions, are verified. Covering all transitions at least once also implies covering all states at least once, but not vice versa. Therefore, option D is not the highest coverage criterion. Option C is the lowest coverage criterion, because it only tests the initial and final states of the system or component, without checking the intermediate states or transitions. Option A is incorrect, because the coverage criteria for state transition based test cases can be determined and compared based on the number of transitions and states covered.Reference= CTFL 4.0 Syllabus, Section 4.2.3, page 49-50.

Answer : C

This answer is correct because Behavior-Driven Development (BDD) is a test-first approach, where tests that express a shared understanding from stakeholders of how the application is expected to work, are first written in business-readable language (following the Given/When/Then format), and then made executable to drive development. BDD is a collaborative approach that involves testers, developers, business analysts, product owners, and other stakeholders in defining the expected behavior of the application using scenarios that describe the preconditions, actions, and outcomes of the application. BDD scenarios are written using a domain-specific language (DSL) that can be translated into executable test cases using tools such as Cucumber or SpecFlow. BDD aims to improve communication, collaboration, and feedback among the team members, and to deliver software that meets the customer's needs and expectations.Reference: ISTQB Glossary of Testing Terms v4.0, ISTQB Foundation Level Syllabus v4.0, Section 3.1.1.4