What is the primary reason to install a monitoring system in the data centre?
Answer : A
The primary reason to install a monitoring system in the data centre is to notice abnormalities early so that actions can be taken to avoid disasters, according to the CDCP Preparation Guide1 and various web sources234. A monitoring system is a system that collects and analyzes data about the power, cooling, environmental, and security conditions in the data centre, and alerts the operators or managers about any issues or threats that may affect the performance, availability, or reliability of the data centre. A monitoring system can help to prevent or minimize the impact of disasters, such as power outages, fire, water damage, overheating, equipment failure, or cyberattacks, by providing timely and accurate information that enables fast and corrective action. A monitoring system can also help to improve the energy efficiency, capacity planning, and asset management of the data centre, by providing useful insights and trends that support informed decision making.
1: CDCP Preparation Guide, page 21, section 2.3.5 2: Improving Data Center Management and Monitoring5, page 1, section 1 3: Guide to Data Center Monitoring6, page 1, section 1 4: Why Data Center Monitoring is Essential7, page 1, section 1
Which type of copper wire is used for grounding the racks to the SRG?
Answer : C
The type of copper wire that is used for grounding the racks to the SRG (signal reference grid) in a data centre is braided copper wire or flat copper strip, according to the CDCP Preparation Guide1 and various web sources234. Braided copper wire or flat copper strip are preferred over thin or thick copper cable for grounding purposes, because they have lower impedance and higher surface area, which allow better dissipation of electrical noise and interference. Moreover, braided copper wire or flat copper strip are more flexible and durable than copper cable, which make them easier to install and maintain. Braided copper wire or flat copper strip should be connected to the SRG using exothermic welding or other code-compliant methods, and should follow the relevant standards and codes, such as ANSI/TIA/EIA-607 and NFPA 70.
1: CDCP Preparation Guide, page 23, section 2.4.2 2: Signal Reference Grid | Enterprise Data Center Design and Methodology5, page 1, section 1 3: Grounding System Ground Rod Stacking Installation - Rain Bird6, page 1, section 1 4: SmartRack Copper Bus Grounding Bar - Eaton Website7, page 1, section 1
The most damaging type of floor load for raised floor tiles in a data centre is the rolling load (RL), according to the CDCP Preparation Guide1 and various web sources234. A rolling load is the load that is applied by a moving object, such as a pallet jack, a forklift, or a rack on wheels. A rolling load can cause more stress and fatigue on the raised floor tiles than a static load, such as a concentrated load (CP) or a uniformly distributed load (UDL), because it creates dynamic forces and impacts that can crack, dent, or deform the tiles. Moreover, a rolling load can also damage the pedestals and stringers that support the tiles, and cause the tiles to become loose or misaligned. Therefore, when designing and installing a raised floor system, it is important to consider the maximum rolling load that the tiles can withstand, and to use appropriate materials and methods to enhance the strength and durability of the tiles. For example, some possible solutions include using steel or concrete-filled tiles, reinforcing the edges and corners of the tiles, and using locking or gravity-held systems to secure the tiles.
1: CDCP Preparation Guide, page 23, section 2.4.2 2: Top 5 Considerations - Selecting a Data Center Raised Floor Tile5, page 1, section 1 3: Raised Floor Systems: Explained, Improved and Reinvented6, page 1, section 1 4: Raised Floor Systems: Common Problems and Solutions7, page 1, section 1
What should be considered when implementing hot- or cold-aisle containment in an existing computer room?
Answer : C
Hot- or cold-aisle containment is a strategy to improve the cooling efficiency and reduce the energy consumption of data centers by isolating the hot exhaust air from the cold supply air. However, implementing this strategy in an existing computer room may create potential issues with the existing fire suppression system(s), such as:
* The containment barriers may interfere with the distribution and activation of the fire suppression agents, such as water, gas, or aerosol, and reduce their effectiveness in extinguishing a fire.
* The containment barriers may create pockets of high temperature and pressure that could damage the equipment or the containment structure itself in the event of a fire.
* The containment barriers may obstruct the access and visibility of the fire detection and alarm devices, such as smoke detectors, heat sensors, or manual call points, and delay the response time of the fire suppression system(s).
* The containment barriers may violate the local fire codes and regulations that specify the minimum clearance and ventilation requirements for the data center.
Therefore, when implementing hot- or cold-aisle containment in an existing computer room, it is important to consider the impact on the existing fire suppression system(s) and take appropriate measures to ensure the safety and compliance of the data center, such as:
* Consulting with the fire authorities and the fire suppression system vendor to assess the compatibility and suitability of the containment solution with the existing fire suppression system(s).
* Modifying or upgrading the existing fire suppression system(s) to accommodate the containment solution, such as relocating or adding fire suppression devices, adjusting the discharge rate and pressure, or installing a secondary fire suppression system within the contained area.
* Installing fire-rated containment barriers that can withstand high temperatures and resist the spread of fire and smoke, and that have self-closing or automatic release mechanisms in case of a fire.
* Installing fire detection and alarm devices within the contained area and ensuring their proper integration and communication with the existing fire suppression system(s).
* Conducting regular testing and maintenance of the fire suppression system(s) and the containment solution to ensure their functionality and reliability.
What should be a consideration when having casters (rollers/wheels) or feet under the rack?
Answer : A
The casters and feet under the rack are used to support the weight of the rack and its equipment, and to allow the rack to be moved if needed. However, the casters and feet should also be designed to avoid putting too much pressure on the floor tile, especially if the data centre uses a raised floor system. A too heavy point load on the floor tile can cause the tile to crack, deform, or collapse, which can damage the rack, the equipment, and the underlying infrastructure. To prevent this, the casters and feet should be larger, so that they can distribute the weight over a larger area and reduce the point load. The casters and feet should also be compatible with the floor type and the load rating of the floor tile.
1: CDCP Preparation Guide, page 22, section 2.4.1.1 2: Raised Floor Design Considerations for Data Center3, page 1, section 1 4: [SOLVED] server rack on casters or feet5, page 1, section 1
Unlock All Features of Exin CDCP Dumps Software
Just have a look at the best and updated features of our CDCP dumps which are described in detail in the following tabs. We are very confident that you will get the best deal on this platform.
Select Question Types you want
Set your desired pass percentage
Allocate Time (Hours: Minutes)
Create Multiple Practice test with limited questions
Customer Support
Latest Success Metrics For actual CDCP Exam
This is the best time to verify your skills and accelerate your career. Check out last week's results, more than 90% of students passed their exam with good scores. You may be the Next successful Candidate.
95%
Average Passing Scores in final Exam
91%
Exactly Same Questions from these dumps
90%
Customers Passed Exin CDCP exam
OUR SATISFIED CUSTOMER REVIEWS
Jorgen Magnus
December 11, 2024
"I had a mixed experience with this platform. There is no platform that offers 100% real exam questions for the DCP exam. However, using Premium dumps made my preparation less challenging because they offer clear explanations to make conceptual understanding better. I think they need more explanations, but they still helped me pass. Thankyou!"
Elias Samuel
December 9, 2024
Using poorly researched practice exams for CDCP topics such as risk management and disaster recovery frustrated me. Unlike others, Premiumdumps reduced my overwhelm by identifying my weaknesses. A simplified, structured, and well-designed resource, recommended!
Alva Sofie
December 7, 2024
Initially, I was forcing myself to cover every topic of the CDCP exam in-depth. It led to time mismanagement and more stress. Topics like redundancy and uptime was hard to fully master in limited time. Thanks a lot guys, your practice exams helped me understand these topics and saved vital time. I passed on the first try.